Dimercaptosuccinic Acid

Active ingredient: 2,3-Dimercaptosuccinic Acid

In short: Technetium Tc 99m DMSA by intravenous administration is indicated as a static kidney imaging agent.

LabelAnazaoHealth Corporation
Label updatedDec 03, 2012

What is Dimercaptosuccinic Acid used for?

Technetium Tc 99m DMSA by intravenous administration is indicated as a static kidney imaging agent.

Dimercaptosuccinic Acid dosage

Preparation of Technetium Tc 99m DMSA is done by the following aseptic procedure:

Waterproof gloves should be worn during the preparation

Snap off the plastic lid and place room temperature reaction vial in an appropriate lead shield.

Swab the rubber closure of the vial with a germicide

Inject as close to 1 cc as possible of sterile additive free sodium pertechnetate Tc 99m injection containing up to 1480 MBq (40 mCi) into the vial freshly eluded within 2 hours from a technetium generator. Be sure to maintain inert atmosphere in vial by introducing as little air as possible during reconstitution. NOTE: If sodium pertechnetate Tc 99m injection must be diluted, use only Low Dissolved Oxygen (LDO)

Secure the lead shield cover. Swirl the vial gently to mix contents and let stand for 15 minutes. Add 1 ml Acetate buffer at this time. (This will interfere with the tagging process if introduced any earlier). Buffer must be added (May be added up to 1 hour after Tc 99m)

Examine vial contents; if the solution is not clear and free of particulate matter and discoloration on visual inspection, it should not be used

Measure the radioactivity by a suitable calibration system and record prior to patient administration

Buffered material should be used within 2 hours

Appropriate quality control is recommended

Tagging Tips

If you need only a one or two mCi dose for your patient, use about 10 mCi of Tc 99m for your kit. Do not stretch your kit to 40 mCi if you do not need to. We have tested the kits to 40 mCi with a Friday generator eluted on Monday but recommend using only what you need

Keep your volumes low. Take your Tc 99m and dilute to about 1cc with the Low Dissolved Oxygen saline and inject into the DMSA kit

Let the kit stand for about 15 minutes with just the Tc 99m and DMSA (NO BUFFER)

After 15 minutes, then add the buffer. This is only for patient comfort and will interfere with the tagging process if introduced any earlier

After buffering you can add additional “Low Dissolved Oxygen” saline to dilute the kit

You should inject the dose within 2 hours after making the kit for best results

Store the kit at 2°-8°C (36°-46°F) and protect from light

Warnings & precautions

Do not take this medicine if: There are no known contraindications.

About this medicine

AnazaoHealth supplies DMSA as a compounded kit for preparing Tc 99m DMSA. Each Reaction vial contains 1.1 mg meso-2, 3-dimercaptosuccinic acid, 0.2 mg tin as stannous chloride, and 0.7 mg ascorbic acid. The vial is back filled with inert gas and may contain a partial vacuum.

Each Acetate buffer vial contains 1.2 ml Sodium Acetate .25 N. pH 5.2 to 5.6.

LDO normal saline included for dilution of prepared kit, if required

How it works: Technetium Tc 99m DMSA, when administered intravenously apparently binds to plasma proteins in the blood and collects in the renal cortex.

Disclaimer: This page is for general information only and is not medical advice. It is a condensed summary of the official FDA-approved label — it does not replace the full prescribing information or the advice of your doctor or pharmacist. Always follow your prescriber's instructions and read the medication guide that comes with your medicine.

Source: FDA-approved label via DailyMed (U.S. National Library of Medicine), label set ID 5b11e596-3044-429b-9e48-33ba00946151. Read the full official label on DailyMed.