Bivalirudin

Active ingredient: Bivalirudin

In short: Bivalirudin Injection is indicated for use as an anticoagulant in patients undergoing percutaneous coronary intervention (PCI), including patients with heparin-induced thrombocytopenia and heparin-induced thrombocytopenia and thrombosis syndrome.

Forms & strengthsInjection, clear to slightly opalescent, colorless to yellow sterile solution: 250 mg of bivalirudin per 50 mL (5 mg/mL) in a single-dose vial. Ready-to-use. …
LabelPar Health USA, LLC
Label updatedJun 22, 2026

What is Bivalirudin used for?

Bivalirudin Injection is indicated for use as an anticoagulant in patients undergoing percutaneous coronary intervention (PCI), including patients with heparin-induced thrombocytopenia and heparin-induced thrombocytopenia and thrombosis syndrome.

Bivalirudin dosage

The recommended dose of Bivalirudin Injection is an intravenous bolus dose of 0.75 mg/kg, followed immediately by a maintenance infusion of 1.75 mg/kg/h for the duration of the procedure. Five minutes after the bolus dose has been administered, assess activated clotting time (ACT) to determine if an additional bolus of 0.3 mg/kg is needed.

Consider extending duration of infusion following PCI at 1.75 mg/kg/h for up to 4 hours post- procedure in patients with ST segment elevation MI (STEMI).

Bolus Dose:

No reduction in the bolus dose is needed for any degree of renal impairment.

Maintenance Infusion:

In patients with creatinine clearance less than 30 mL/min (by Cockcroft Gault equation), reduce the infusion rate to 1 mg/kg/h.

In patients on hemodialysis, reduce the infusion rate to 0.25 mg/kg/h .

Bivalirudin Injection is a ready-to-use sterile solution for intravenous use only.

Inspection of Container

Parenteral drug products should be inspected visually for particulate matter and discoloration prior to administration, whenever solution and container permit.

Once removed from the refrigerator, Bivalirudin Injection may be stored at room temperature 20º to 25°C (68º to 77°F) for up to 72 hours . Discard any unused portion.

Drug Compatibilities

No incompatibilities have been observed with administration sets.

Do not administer the drugs listed in Table 1 in the same intravenous line with Bivalirudin Injection.

Table 1. Drugs Not for Administration in the Same Intravenous Line with Bivalirudin Injection

Alteplase

Amiodarone HCl

Amphotericin B

Chlorpromazine HCl

Diazepam

Dobutamine

Prochlorperazine Edisylate

Reteplase

Streptokinase

Vancomycin HCl

How to take Bivalirudin — instructions & advice from the label

Advise patients to watch carefully for any signs of bleeding or bruising and to report these to their healthcare provider when they occur.

Manufactured for:

Par Health USA

Rochester, MI 48307

Product of India

R12/2025

Warnings & precautions

Do not take this medicine if: Bivalirudin Injection is contraindicated in patients with:

Significant active bleeding;

Hypersensitivity to Bivalirudin Injection or its components .

Bivalirudin increases the risk of bleeding . Bivalirudin’s anticoagulant effect subsides approximately one hour after discontinuation .

An increased risk of thrombus formation, including fatal outcomes, has been associated with the use of bivalirudin in gamma brachytherapy .

Bivalirudin side effects

Because clinical trials are conducted under widely varying conditions, adverse reaction rates observed in the clinical trials of a drug cannot be directly compared to rates in the clinical trials of another drug and may not reflect the rates observed in practice.

In the BAT trials, 79 of the 2161 (3.7%) of subjects undergoing PCI for treatment of unstable angina and randomized to bivalirudin experienced intracranial bleeding, retroperitoneal bleeding, clinically overt bleeding with a decrease in hemoglobin greater than 3 g/dL or leading to a transfusion of greater than 2 units of blood.

Immunogenicity/Re-Exposure

As with all therapeutic proteins, there is potential for immunogenicity. The detection of antibody formation is highly dependent on the sensitivity and specificity of the assay. Additionally, the observed incidence of antibody (including neutralizing antibody) positivity in an assay may be influenced by several factors including assay methodology, sample handling, timing of sample collection, concomitant medications, and underlying disease. For these reasons, comparison of the incidence of antibodies to bivalirudin in the studies described below with the incidence of antibodies in other studies or to other products may be misleading.

In in vitro studies, bivalirudin exhibited no platelet aggregation response against sera from patients with a history of HIT/HITTS. …

Drug interactions

In clinical trials in patients undergoing PCI, co-administration of bivalirudin with heparin, warfarin, thrombolytics, or GPIs was associated with increased risks of major bleeding events compared to patients not receiving these concomitant medications.

About this medicine

Bivalirudin Injection contains bivalirudin trifluoroacetate, which is a specific and reversible direct thrombin inhibitor. Bivalirudin trifluoroacetate is a synthetic, 20 amino acid peptide salt, with the chemical name of D-phenylalanyl-L-prolyl-L-arginyl-L-prolylglycylglycylglycylglycyl-L-asparagylglycyl-L-α-aspartyl-L-phenylalanyl-L-α-glutamyl-L-α-glutamyl-L-isoleucyl-L-prolyl-L-α-glutamyl-L-α-glutamyl-L-tyrosyl-L-leucine trifluoroacetate. Each molecule of bivalirudin trifluoroacetate contains 1.7 to 2.6 equivalents of trifluoroacetic acid. The molecular formula of bivalirudin free base is C98H138N24O33 and its molecular weight is 2180.32 Daltons (anhydrous free base peptide). The structural formula of bivalirudin free base is

Figure 1: Structural Formula of Bivalirudin

Bivalirudin Injection is supplied as a refrigerated, ready-to-use, sterile solution packaged in a 50 mL single-dose vial. Each milliliter of Bivalirudin Injection contains 5 mg bivalirudin (as trifluoroacetate salt)*, 0.8 mg sodium acetate trihydrate, 100 mg polyethylene glycol 400, and Water for Injection. …

Disclaimer: This page is for general information only and is not medical advice. It is a condensed summary of the official FDA-approved label — it does not replace the full prescribing information or the advice of your doctor or pharmacist. Always follow your prescriber's instructions and read the medication guide that comes with your medicine.

Source: FDA-approved label via DailyMed (U.S. National Library of Medicine), label set ID 91cf9d00-29e0-4357-a184-f70026c47edb. Read the full official label on DailyMed.

Related medicines

Apixaban Warfarin Fondaparinux Dabigatran Dalteparin Edoxaban Enoxaparin Heparin